...
Step 1 - Determine logger modstate
See Determine the Mod State of an SA380TX.
Step 2 - Determine current and target firmware, and upgrade method
Based on the modstate determined in step 1:
Modstate 3+
Platform | firmware < 1144 (including 1.5T446-3G-B) | from firmware ≥ 1144 | 1319 | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Centrix Upgrade to
| Use 1319 USB ZIP file:
| Use 1319 UPG file:
|
| ||||||||||||
NR II / RADAR (Private APN with IP access) Upgrade to
| Use 1319 ZIP files:
| Use 1319 UPG file:
|
| ||||||||||||
Not connected to any system | Use 1319 USB ZIP file:
| Use 1319 UPG file:
|
Upgrading a Mod State 1 or Mod State 2 SA380TX with a USB drive, using the "Centrix Approved" .ZIP firmware package for USB drives
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS1/2
Firmware that is "Centrix Approved".
Pre-formatted to work with USB drives
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
2) Follow the instructions for SA380TX - Firmware Upgrade from .ZIP files using a USB Drive using the firmware package just downloaded.
...
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS1/2
Firmware that is "Centrix Approved".
Pre-formatted to work with dUpgrade
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
2) Follow the instructions for SA380TX - Firmware Upgrade using dUpgrade using the firmware package just downloaded.
...
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS1/2
Firmware that is "NR II Approved".
Pre-formatted to work with USB drives
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
2) Follow the instructions for SA380TX - Firmware Upgrade from .ZIP files using a USB Drive using the firmware package just downloaded.
...
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS1/2
Firmware that is "NR II Approved".
Pre-formatted to work with dUpgrade
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
2) Follow the instructions for SA380TX - Firmware Upgrade using dUpgrade using the firmware package just downloaded.
...
As of firmware release 1144, The SA380TX now supports the universal Mpec UPG firmware file format. In order to be able to use this new file format, you will have to first upgrade your firmware via a "stepping stone" version. After which, a further upgrade is required using the new UPG file.
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "Stepping Stone".
Pre-formatted to work with USB drives
2) Follow the instructions for SA380TX - Firmware Upgrade from .ZIP files using a USB Drive using the firmware package just downloaded.
3) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "Centrix Approved".
Download the UPG File
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
4) Follow the instructions for SA380TX - Firmware Upgrade from .UPG files using a USB Drive using the firmware package just downloaded.
...
As of firmware release 1144, The SA380TX now supports the universal Mpec UPG firmware file format. In order to be able to use this new file format, you will have to first upgrade your firmware via a "stepping stone" version. After which, a further upgrade is required using the new UPG file.
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "Stepping Stone".
Pre-formatted to work with dUpgrade
2) Follow the instructions for SA380TX - Firmware Upgrade using dUpgrade using the firmware package just downloaded.
...
As of firmware release 1144, The SA380TX now supports the universal Mpec UPG firmware file format. In order to be able to use this new file format, you will have to first upgrade your firmware via a "stepping stone" version. After which, a further upgrade is required using the new UPG file.
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "Stepping Stone".
Pre-formatted to work with USB drives
2) Follow the instructions for SA380TX - Firmware Upgrade from .ZIP files using a USB Drive using the firmware package just downloaded.
3) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "NR-II Approved".
Download the UPG File
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
4) Follow the instructions for SA380TX - Firmware Upgrade from .UPG files using a USB Drive using the firmware package just downloaded.
...
As of firmware release 1144, The SA380TX now supports the universal Mpec UPG firmware file format. In order to be able to use this new file format, you will have to first upgrade your firmware via a "stepping stone" version. After which, a further upgrade is required using the new UPG file.
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "Stepping Stone".
Pre-formatted to work with dUpgrade
2) Follow the instructions for SA380TX - Firmware Upgrade using dUpgrade using the firmware package just downloaded.
3) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "NR-II Approved".
Download the UPG File
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
4) Follow the instructions for SA380TX - Firmware Upgrade using dUpgrade using the firmware package just downloaded.
...
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "Centrix Approved".
Download the UPG File
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
2) Follow the instructions for SA380TX - Firmware Upgrade from .UPG files using a USB Drive using the firmware package just downloaded.
...
Firmware Upgrade is fully integrating into the Centrix platform, follow the instructions for SA380TX - Firmware Upgrade using Centrix to perform the the upgrade
...
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "NR-II Approved".
Download the UPG File
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
...
Modstate 1/2
Platform | firmware < 1.5T446-3G-B | 1.5T446-3G-B | 311 | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Centrix Upgrade to
| Use 311 USB ZIP file:
|
| |||||||||||||||||||
NR II / RADAR (Private APN with IP access) Upgrade to
| Use 1.5T446-3G-B ZIP files:
|
|
| ||||||||||||||||||
Not connected to any system | Use 311 USB ZIP file:
| ||||||||||||||||||||
Step 3 - Find the appropriate files
| Info |
|---|
If you’re upgrading remotely from Centrix, you can skip this step! |
Based on the modstate, target firmware and upgrade method, download the appropriate file from the firmware downloads page.
Step 4 - Follow the appropriate instructions:
Upgrading with USB on site
SA380TX - Firmware Upgrade from .ZIP files using a USB Drive
SA380TX - Firmware Upgrade from .UPG files using a USB Drive using the firmware package just downloaded.Anchor
1) Visit the Mpec Firmware Downloads Page and download the firmware package with the following properties:
...
For SA380TX MS3+
Firmware that is labelled "NR-II Approved".
Download the UPG File
| Info |
|---|
New firmware is released regularly, and approval status may change. Following the guidance above will always steer you towards the correct firmware package. |
2) Follow the instructions for SA380TX - Firmware Upgrade using dUpgrade using the firmware package just downloaded.
Upgrading remotely with dUpgrade
SA380TX - Firmware Upgrade using dUpgrade