Page Comparison

...

4-20mA Sensor Tables

...

Part No.

...

Variant Description

...

Quantity

...

Quantity Description

...

Value @ 4mA

...

Value @ 20mA

...

Units

...

Suggested AoC

...

RS485 Sensor Tables

VTI21-VT1

...

Slave Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

VTI21-TI21 / VTI21-FS25 / VTI21-FS26

...

Slave Channel

...

VTI21 Input Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

4-20mA Sensor Tables

Part No.	Variant Description	Quantity	Quantity Description	Value @ 4mA	Value @ 20mA	Units	Suggested AoC
VTI21-VT1	AC Vane Relay Variant	Torque	Instantaneous Torque Exerted on the relay vane.	0	+25	m.Nm	0.2 m.Nm
VTI21-HVI	HVI Receiver Variant	Average Current	Average HVI Pulsed Current seen by the VTI21 from input channel 1.	0	600	mA	15 mA
VTI21-TI21-TX	TI21 / EbiTrack 200 Variant (TX)	Average Current	Average of upper and lower sideband current from VTI21 input channel 1.	0	5	A	0.05 A
VTI21-TI21-TX	TI21 / EbiTrack 200 Variant (RX)	Average Current	Average of upper and lower sideband current from VTI21 input channel 1.	0	200	mA	2 mA
VTI21-FS25	FS2500 Receiver Variant	Center Current	Amplitude of the FS2500 center frequency current from VTI21 input channel 1.	0	1500	mA	5 mA
VTI21-FS26	FS2600 Receiver Variant	Center Current	Amplitude of the FS2500 center frequency current from VTI21 input channel 1.	0	1500	mA	5 mA
VTI21-ACS	General Purpose AC sensing up to 25A RMS	Current	RMS current from VTI21 input channel 1.	0	25	A	0.2 A
VTI21-UM71	UM71 Variant	Current	Current at selected center frequency from VTi21 input channel 1.	0	5000	µA	100µA
VTI21-ASTER	Aster Variant	Current	Current at selected center frequency from VTi21 input channel 1.	0	5000	µA	100µA
VTI21-REED	Reed Relay Variant	Current	Current measured across the Reed relay frequency range on input channel 1.	0	5000	mA	25mA
VTI21-RFDM	Reed Relay FDM variant	n/a	none

RS485 Sensor Tables

VTI21-VT1

Slave Channel	Quantity	Description	Typical Range	Units	Suggested AoC
1	Torque	Instantaneous torque exerted on the relay vane	-25 to +25	m.Nm	0.2 m.Nm
2	Phase	Phase angle between local coil and control coil currents	0 to 180	Degrees	2 degrees
3	Local Current	RMS current in the local coil	0 to 500	mA	5 mA
4	Control Current	RMS current in the track coil	0 to 1000	mA	5 mA
5	Chatter	Degree of chatter	0 to 100	%	5 %

VTI21-TI21 / VTI21-FS25 / VTI21-FS26

Slave Channel	VTI21 Input Channel	Quantity	Description	Typical Range	Units	Suggested AoC
1	1	Center Frequency	The Center frequency, in hertz, of the track circuit.	388.8 to 508.8	Hz	1 Hz
2		Center frequency Current	Total RMS current at the target center frequency	0 to 1000	mA	5 mA
3		Lower Side Band current	Total RMS current at the target lower side band frequency	0 to 1000	mA	5 mA
4		Upper Side Band current	Total RMS current at the target upper side band frequency	0 to 1000	mA	5 mA
5		In Band Current	Total RMS current seen by the transducer between 300 to 600 Hz	0 to 1000	mA	5 mA
6		Spectrogram or Gain	Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram. When spectrum data is not being acquired, this channel shows the current amplifier gain setting	4.8 to 1228.8	Hz	NA
7		Loudest Frequency	The strongest frequency, in hertz, observed in the incoming waveform.	4.8 to 1228.8	Hz	1 Hz
8		Total Current	Total RMS current seen by the transducer.	0 to 1000	mA	5 mA
9	2	Center Frequency	The Center frequency, in hertz, of the track circuit.	388.8 to 508.8	Hz	1 Hz

21

10

Center frequency Current

Total RMS current at the target center frequency

0 to 1000

mA

5 mA

3

11

1

Lower Side Band current

Total RMS current at the target lower side band frequency

0 to 1000

mA

5 mA

41

12

Upper Side Band current

Total RMS current at the target upper side band frequency

0 to 1000

mA

5 mA

5

13

1

In Band Current

Total RMS current seen by the transducer between 300 to 600 Hz

0 to 1000

mA

5 mA

6

14

1

Spectrogram

or Gain

Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram.

When spectrum data is not being acquired, this channel shows the current amplifier gain setting

4.8 to 1228.8

Hz

NA

7

15

1

Loudest Frequency

The strongest frequency, in hertz, observed in the incoming waveform.

4.8 to 1228.8

Hz

1 Hz

81

16

Total Current

Total RMS current seen by the transducer.

0 to 1000

mA

5 mA92Center

5 mA

VTI21-HVI

...

Slave Channel

VTI21 Input Channel

Quantity

Description

Typical Range

Units

Suggested AoC

1 - ANA

1

HVI Frequency

The

Center

frequency

, in hertz, of the track circuit.388.8 to 508.8

of pulses

0 to 5

Hz

0.1 Hz

102Center frequency CurrentTotal RMS current at the target center frequency0 to 1000

2 - ANA	HVI Current	RMS Current of the pulsed waveform	0 to 1500	mA	5 mA
3 - ANA	Noise Current	The RMS current observed between pulses.	0 to 1500	mA	5 mA

112Lower Side Band currentTotal RMS current at the target lower side band frequency0 to 1000mA5 mA122Upper Side Band currentTotal RMS current at the target upper side band frequency0 to 1000mA5 mA132In Band CurrentTotal RMS current seen by the transducer between 300 to 600 Hz0 to 1000mA5 mA142

Spectrogram

or Gain

Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram.

When spectrum data is not being acquired, this channel shows the current amplifier gain setting

4.8 to 1228.8HzNA152Loudest FrequencyThe strongest frequency, in hertz, observed in the incoming waveform.4.8 to 1228.8Hz1 Hz162Total CurrentTotal RMS current seen by the transducer.0 to 1000mA5 mA

VTI21-HVI

...

Slave Channel

...

VTI21 Input Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

VTI21-ACS-001

...

Slave Channel

...

VTI21 Input Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

VTI21-ACS-020

...

Slave Channel

...

VTI21 Input Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

Slave Channel

...

VTI21 Input Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

CH 1 Spectrogram or Gain

...

Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram.

...

CH 2 Spectrogram or Gain

...

Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram.

...

VTI21-Reed

...

Slave Channel

...

VTI21 Input Channel

...

Quantity

...

Description

...

Typical Range

...

Units

...

Suggested AoC

...

CH 1 - channel 211

...

Total Current at 363Hz

...

CH 1 - channel 212

...

Total Current at 366Hz

...

CH 1 - channel 213

...

Total Current at 369Hz

...

CH 1 - channel 214

...

Total Current at 372Hz

...

CH 1 - channel 215

...

Total Current at 375Hz

...

CH 1 - channel 216

...

Total Current at 378Hz

...

CH 1 - channel 217

...

Total Current at 381Hz

...

CH 1 - channel 218

...

Total Current at 384Hz

...

Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram. note: includes only measured frequencies, which are: 363, 366, 369, 372, 375, 378, 381, 384, 408, 417, 423Hz

...

CH 2 - channel 211

...

Total Current at 363Hz

...

CH 2 - channel 212

...

Total Current at 366Hz

...

CH 2 - channel 213

...

Total Current at 369Hz

...

CH 2 - channel 214

...

Total Current at 372Hz

...

CH 2 - channel 215

...

Total Current at 375Hz

...

CH 2 - channel 216

...

Total Current at 378Hz

...

CH 2 - channel 217

...

Total Current at 381Hz

...

CH 2 - channel 218

...

Total Current at 384Hz

...

Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram. note: includes only measured frequencies, which are: 363, 366, 369, 372, 375, 378, 381, 384, 408, 417, 423Hz

4 - DIG	Pulse Conflict	Set TRUE if pulses are observed to be bleeding through from adjacent track sections	Digital	N/A	On Change
5 - ANA	Rejection Rate	Proportion of pulses deemed not to be genuine HVI pulses	0 to 100	%	Don't push to server - for diagnostic use by Mpec only
6 - ANA	Rejection Reason	Bitfield encoding the reason a pulse was not accepted.	8 bits	N/A
7- ANA	Sensitivity	Threshold used to identify pulse events	0 to 2621440	N/A
8 - ANA	Pulse Waveform	If this channel is requested as a capture, the VTi21 will return a high-resolution waveform of the last observed pulse	0 to 1500	mA	Triggered Capture
9 - ANA	2	HVI Frequency	The frequency of pulses	0 to 5	Hz	0.1 Hz
10 - ANA		HVI Current	RMS Current of the pulsed waveform	0 to 1500	mA	5 mA
11 - ANA		Noise Current	The RMS current observed between pulses.	0 to 1500	mA	5 mA
12 - DIG		Pulse Conflict	Set TRUE if pulses are observed to be bleeding through from adjacent track sections	Digital	N/A	On Change
13 - ANA		Rejection Rate	Proportion of pulses deemed not to be genuine HVI pulses	0 to 100	%	Don't push to server - for diagnostic use by Mpec only
14 - ANA		Rejection Reason	Bitfield encoding the reason a pulse was not accepted.	8 bits	N/A
15 - ANA		Sensitivity	Threshold used to identify pulse events	0 to 2621440	N/A
16 - ANA		Pulse Waveform	If this channel is requested as a capture, the VTi21 will return a high-resolution waveform of the last observed pulse	0 to 1500	mA	Triggered Capture

VTI21-ACS

Slave Channel	VTI21 Input Channel	Quantity	Description	Typical Range	Units	Suggested AoC
1	1	CH 1 Current	RMS current observed on Channel 1 (output at 100 Hz, low pass filtered with cutoff of 9 Hz)	0 to 25	A	0.2 A
2	1	CH 1 Average Current	Average RMS current observed on Channel 1, over one second period.	0 to 25	A	0.2 A
3	2	CH 2 Current	RMS current observed on Channel 2 (output at 100 Hz, low pass filtered with cutoff of 9 Hz)	0 to 25	A	0.2 A
4	2	CH 2 Average Current	Average RMS current observed on Channel 2, over one second period.	0 to 25	A	0.2 A

VTI21-UM71

Slave Channel	VTI21 Input Channel	Quantity	Description	Typical Range	Units	Suggested AoC
1	1	CH 1 Frequency	Channel 1 Frequency Selected	1700 to 2600	Hz	1
2		CH 1 Side Band Ratio	Ratio of lower to upper frequency (0%=all lower, 100%=all upper)	0 to 100%	%	5
3		CH 1 Raw Frequency	Simple Frequency Measurement (zero crossings)	1600 to 2700	Hz	100
4		CH 1 Total Current	Total current in the UM71 band	0 to 5mA	µA	100
5		CH 1 current 1700Hz	Current measured at 1700Hz	0 to 5mA	µA	100
6		CH 1 current 2000Hz	Current measured at 2000Hz	0 to 5mA	µA	100
7		CH 1 current 2300Hz	Current measured at 2300Hz	0 to 5mA	µA	100
8		CH 1 current 2600Hz	Current measured at 2600Hz	0 to 5mA	µA	100
9		CH 1 Spectrogram or Gain	Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram.	1 to 32		1
10	2	CH 2 Frequency	Channel 1 Frequency Selected	1700 to 2600	Hz	1
11		CH 2 Side Band Ratio	Ratio of lower to upper frequency (0%=all lower, 100%=all upper)	0 to 100%	%	5
12		CH 2 Raw Frequency	Simple Frequency Measurement (zero crossings)	1600 to 2700	Hz	100
13		CH 2 Total Current	Total current in the UM71 band	0 to 5mA	µA	100
14		CH 2 current 1700Hz	Current measured at 1700Hz	0 to 5mA	µA	100
15		CH 2 current 2000Hz	Current measured at 2000Hz	0 to 5mA	µA	100
16		CH 2 current 2300Hz	Current measured at 2300Hz	0 to 5mA	µA	100
17		CH 2 current 2600Hz	Current measured at 2600Hz	0 to 5mA	µA	100
18		CH 2 Spectrogram or Gain	Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram.	1 to 32		1

VTI21-Reed

Slave Channel	VTI21 Input Channel	Quantity	Description	Typical Range	Units	Suggested AoC
1	1	CH 1 Frequency	Simple Frequency Measurement (zero crossings)	0 to 5000	Hz	1
2		CH 1 Total Current	Total current measured in the reed relay frequency range	0 to 5000	mA	10
3		CH 1 - channel 211	Total Current at 363Hz	0 to 5000	mA	10
4		CH 1 - channel 212	Total Current at 366Hz	0 to 5000	mA	10
5		CH 1 - channel 213	Total Current at 369Hz	0 to 5000	mA	10
6		CH 1 - channel 214	Total Current at 372Hz	0 to 5000	mA	10
7		CH 1 - channel 215	Total Current at 375Hz	0 to 5000	mA	10
8		CH 1 - channel 216	Total Current at 378Hz	0 to 5000	mA	10
9		CH 1 - channel 217	Total Current at 381Hz	0 to 5000	mA	10
10		CH 1 - channel 218	Total Current at 384Hz	0 to 5000	mA	10
11		CH 1 - spectrogram / gain	Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram. note: includes only measured frequencies, which are: 363, 366, 369, 372, 375, 378, 381, 384, 408, 417, 423Hz
12	2	CH 2 Frequency	Simple Frequency Measurement (zero crossings)	0 to 5000	Hz	1
13		CH 2 Total Current	Total current measured in the reed relay frequency range	0 to 5000	mA	10
14		CH 2 - channel 211	Total Current at 363Hz	0 to 5000	mA	10
15		CH 2 - channel 212	Total Current at 366Hz	0 to 5000	mA	10
16		CH 2 - channel 213	Total Current at 369Hz	0 to 5000	mA	10
17		CH 2 - channel 214	Total Current at 372Hz	0 to 5000	mA	10
18		CH 2 - channel 215	Total Current at 375Hz	0 to 5000	mA	10
19		CH 2 - channel 216	Total Current at 378Hz	0 to 5000	mA	10
20		CH 2 - channel 217	Total Current at 381Hz	0 to 5000	mA	10
21		CH 2 - channel 218	Total Current at 384Hz	0 to 5000	mA	10
22		CH 2 - spectrogram / gain	Capture waveform showing the magnitude spectrum of the input signal. Use a "Triggered Capture" to acquire the Spectrogram. note: includes only measured frequencies, which are: 363, 366, 369, 372, 375, 378, 381, 384, 408, 417, 423Hz

Aster

Slave Channel	VTI21 Input Channel	Quantity	Description	Typical Range	Units	Suggested AoC Threshold
1	1	Lock-on Frequency	Ideal operating frequency track circuit	1700 to 2600	Hz	1
2		In-band Current	RMS current in the operating band	0-5000	uA	50
3		Principle Frequency	Loudest frequency observed (actual operating frequency)	1700 to 2600	Hz	1
4		Total Current	broad-and RMS current	0-5000	uA	50
5		1700 Hz Band Current	RMS current in the 1700 Hz band	0-5000	uA	50
6		2000 Hz Band Current	RMS current in the 1900 Hz band	0-5000	uA	50
7		2300 Hz Band Current	RMS current in the 2100 Hz band	0-5000	uA	50
8		2600 Hz Band Current	RMS current in the 2300 Hz band	0-5000	uA	50
9		Gain / FFT	Pre-amp Gain as AoC, Spectrogram is acquired as a triggered capture	10	Hz	NA
10	2	Lock-on Frequency	Ideal operating frequency track circuit	1700 to 2600	Hz	1
11		In-band Current	RMS current in the operating band	0-5000	uA	50
12		Principle Frequency	Loudest frequency observed (actual operating frequency)	1700 to 2600	Hz	1
13		Total Current	broad-and RMS current	0-5000	uA	50
14		1700 Hz Band Current	RMS current in the 1700 Hz band	0-5000	uA	50
15		2000 Hz Band Current	RMS current in the 1900 Hz band	0-5000	uA	50
16		2300 Hz Band Current	RMS current in the 2100 Hz band	0-5000	uA	50
17		2600 Hz Band Current	RMS current in the 2300 Hz band	0-5000	uA	50
118		Gain / FFT	Pre-amp Gain as AoC, Spectrogram is acquired as a triggered capture	10	Hz	NA

VTI21-RFDM

note: only one input channel is supported.

Slave Channel	VTI21 Input Channel	Quantity	Description	Typical Range	Units	Suggested AoC

Threshold

1

Lock-on Frequency Ideal operating frequency track circuit1700 to 2600

Frequency

Simple Frequency Measurement (zero crossings)

0-1000

Hz

1

50

2

1In-band

Total Current

RMS

Total current measured in the

operating band

reed relay frequency range

0-

5000

5A

uA

mA

501

100

3

1Principle FrequencyLoudest frequency observed (actual operating frequency)1700 to 2600HzNA

FFT	FFT for each monitored Channel		Hz	NA
4

1Total Currentbroad-and RMS current0-5000uA50511700 Hz Band CurrentRMS current in the 1700 Hz band0-5000uA50612000 Hz Band CurrentRMS current in the 1900 Hz band0-5000uA50712300 Hz Band CurrentRMS current in the 2100 Hz band0-5000uA50812600 Hz Band CurrentRMS current in the 2300 Hz band0-5000uA5091Gain / FFTPre-amp Gain as AoC, Spectrogram is acquired as a triggered capture10HzNA102Lock-on Frequency Ideal operating frequency track circuit1700 to 2600Hz1112In-band CurrentRMS current in the operating band0-5000uA50122Principle FrequencyLoudest frequency observed (actual operating frequency)1700 to 2600Hz1132Total Currentbroad-and RMS current0-5000uA501421700 Hz Band CurrentRMS current in the 1700 Hz band0-5000uA501522000 Hz Band CurrentRMS current in the 1900 Hz band0-5000uA501622300 Hz Band CurrentRMS current in the 2100 Hz band0-5000uA501722600 Hz Band CurrentRMS current in the 2300 Hz band0-5000uA501182Gain / FFTPre-amp Gain as AoC, Spectrogram is acquired as a triggered capture10Hz

channel 4	Energy at 803.25Hz	0-5A	mA	100
5	channel 16	Energy at 702.5Hz	0-5A	mA	100
6	channel 17	Energy at 697.5Hz	0-5A	mA	100
7	channel 19	Energy at 687Hz	0-5A	mA	100
8	channel 20	Energy at 682.5Hz	0-5A	mA	100
9	channel 26	Energy at 611.75Hz	0-5A	mA	100
10	channel 27	Energy at 607.75Hz	0-5A	mA	100
11	channel 36	Energy at 505Hz	0-5A	mA	100
12	channel 38	Energy at 493.5Hz	0-5A	mA	100
13	channel 39	Energy at 488Hz	0-5A	mA	100
14	channel 47	Energy at 419.75Hz	0-5A	mA	100
15	channel 48	Energy at 410.25Hz	0-5A	mA	100
16	channel 83	Energy at 446Hz	0-5A	mA	100
17	channel 84	Energy at 533.75Hz	0-5A	mA	100
18	channel 92	Energy at 842Hz	0-5A	mA	100

Versions Compared

Old Version 9

New Version Current

Key

4-20mA Sensor Tables

RS485 Sensor Tables

VTI21-VT1

VTI21-TI21 / VTI21-FS25 / VTI21-FS26

4-20mA Sensor Tables

RS485 Sensor Tables

VTI21-VT1

VTI21-TI21 / VTI21-FS25 / VTI21-FS26

VTI21-HVI

VTI21-HVI

VTI21-ACS-001

VTI21-ACS-020

VTI21-ACS

VTI21-UM71