Assets

The following three asset types have been added to Centrix:

• HVI Track Circuit
• Bus Bar
• HXP-3

Generic Asset Improvements

A number of improvements have been made to the way assets are viewed within Centrix.

• Display of current channel data
• links from the playback tab to graphs
• 'Asset Channel States' component added to Points Asset playback pages.

HVI Track Circuit Asset

The new "HVI Track Circuit" asset is for use with HVI Track circuits monitored using the Mpec VTI21 smart sensor and an SA380-TXcombined with an SA380TX. Please see  https://mpec.co.uk/downloads/VTI21_Datasheet.pdf for the product data sheet. The Asset asset creation page will suggest channel prefixes based on the configuration of the SA380-TXSA380TX, and the channel names found on the selected site:

Image RemovedImage Added

The Auto-detect button will use the chosen prefix to find and fill in the channels required:

Image RemovedImage Added

noteNote: If the channels have been re-named renamed on the logger, or in the mimosa MIMOSA configuration then Centrix may be unable to fill in these values automatically. The Enable Identification of Occupation checkbox  and Enable asset feature channels checkboxes should be checked so that centrix Centrix can generate occupation data for the HVI Track circuit.

The HVI Asset playback page displays occupations and historic track clear current:

current values:

Image Removed

Bus Bar

The bus bar asset type The current value of various asset channels at the selected time is also shown. The buttons to the right allow you to inspect a list of events for the channel (magnifying glass button) or plot the data on a new graph (graph button). Additionally the "View all on Graph" button at the top right will create a new graph with all of the channels.

Image Added

Alarms can now be generated directly from the asset page by selecting the "Alarms" tab, checking one ore more of the missing asset alarms and using the "Generate Selected Alarms" button (see Asset Alarms for more information):

Image Added

Bus Bar Asset

The new "Bus Bar" asset is for use with the Mpec SA380-IT Insulation insulation monitor device. For information on this product, please see https://mpec.co.uk/downloads/SA380-IT_Datasheet.pdf. Configuration of this asset type is currently a manual operation , and the asset definition requires the following channel configuration:

The Bus Bar asset type does not have any specific alarms available, normal analogue level alarms can be setup and will be automatically attached to the asset. The following shows an analogue level alarm , associated with a Bus Bar asset:

The Asset playback page shows these channels and provides links to graph the data:

Alarms can be generated directly from the asset's page by selecting 'alarms' using the 'Generate Selected Alarms' button:

Image Removed

HXP-3 Track Circuit Asset

The "HXP-3 Asset Track Circuit" asset is for HXP-3 Predictor predictor systems. An Mpec S-LX logger can process the live data stream and push it to centrixCentrix. One HXP-3 controller handles one track, normally covering the approach to a level crossing. Centrix splits this into two halves, which are normally named "Track1_XX" and "Track2_XX" on the logger. The Asset collates all the associated channels for the approach circuit:

Note that the "Track Idle" channel should be associated with the loggers "Track1_XX:Track2_XX:Idle" channel. This is raised by the logger when the HXP-3 stops sending data.

There are currently no specific HXP-3 Alarms, however analogue and digital alarms can be created as normal and will be associated with the HXP-3 asset using their channel names.

"Enable Identification of Occupations" should be checked. This enables Centrix to identify track occupations which can be examined using the "playback" tab of the asset page:

Asset Alarms

Anchor
AssetAlarms AssetAlarms

Assets are now able to show which alarms they could have.

The Missing Asset Alarms list displays all of the alarms that this asset does not and should have.
Alarms from this list can be automatically generated by selecting an alarm type, shown by the checked checkbox, and clicking Generate Selected Alarms.

Some of the more complex alarms have to be trained using an alarm wizard, in these cases a link to the relevant alarm wizard will be shown instead of a checkbox.

Health Dashboards

The A minor change to the health dashboards list has been updated to match the format of other lists within Centrixapplied to make it consistent with other list pages in Centrix.

Loggers

MIMOSA Logger - Unassign Site

User Users can now remove Site the site from MIMOSA type loggers. This will disable logger. User loggers, previously it was only possible to change to another site, this will also disable the logger. It will not be able possible to enable a MIMOSA logger if no Site specified on logger.Image Removedunit a site is assigned to the logger again.

Bulk Upgrade

User Users can now filter the logger (s) list by '"Auto Upgrade'".

Channels

When viewing a channel in Centrix any loggers associated with that channel are now shown.

Image Added

Playback Improvements

The playback map now shows route lights on the playback map:

The timezone offset is now displayed next to the date and time on playback:

Image Added

Minor amendments and fixed issues

• Automatic Track Circuit Alarm Wizard page shows threshold graph on a small screens.
• Alarms icon updated to warning triangle.
• Archived channels are no longer shown on Channels Selectorchannel selector.
• Creating 'New Channel' with existing channel Name, Site and channel Type gives validation error.
• Users without permissions to view assets will no longer be presented with an "Assets" link.
• Change Password button now works as expected.

Addendum 95.1 Hotfix Release

• Removed "Edit" button from Playback for users who do not have permission to access the map designer.
• Track circuit occupation graph will now show on alarm raises for "Audio Frequency Track Circuit" alarms if occupations are enabled on the asset.

Addendum 95.2 Hotfix Release

• Fix related to the loading of points alarm at application startup.

Addendum 95.3 Hotfix Release

• Fix for "Banner" signals showing incorrect state on playback map.
• Fix for "Position Light" signals showing incorrect state on playback map.
• Fix for missing shaded region when inspecting points assets (representing inrush current or locking phase).

Addendum 95.4 Hotfix Release

• Fix for signals showing the incorrect state in certain situations.

Addendum 95.5 Hotfix Release

• Fix for user list filtering.